Introducing: The Steam STX N55 BMW Twin Turbocharger Upgrade

Steam STX N55 BMW Turbocharger Upgrade
Steam STX N55 BMW Turbocharger Upgrade

We’ve been manufacturing Subaru-only turbochargers for some time now.  That is mostly because we started doing this because we are Subaru enthusiasts.  That being said, our capabilities stretch to other brands.   Now we are offering a twin turbo upgrade kit for both prospective stage 1 or stage 2 applications.

This is a legitimate turbo upgrade; meaning, it is designed for the factory location.  We supply a new balanced CHRA, complete with new turbine wheel and billet compressor wheel in 62mm or 67mm, depending on what your goals are, and you install that CHRA in your existing turbine housing, attach the compressor housing and all other factory accessories, such as the blow off valve and the wastegate actuator.

Steam STX N55 Compressor Housing and CHRA
Steam STX N55 Compressor Housing and CHRA

With supporting mods, this kit is 600whp capable (stage 2).   Because we are using our 9-blade technology, the spool is still quick and peak flow is there for high rpm performance.

As one might expect, these are manufactured with the same strict attention to detail that we have exhibited in the past with all of our Subaru turbochargers.  They have superior internals and excellent balance characteristics; everything one needs for high octane, high RPM enjoyment.

Want more information? Give us a call at +1 (206) 607-9149 or visit our site.

Supporting Modifications and Your Turbocharger’s Efficiency

Occasionally, we have the opportunity to help our customer troubleshoot situations where their expectations are not being met after installing one of our turbochargers.  This sounds bad initially, but hear me out.

For a moment, consider that a turbocharger is a lot like a big barrel of water.  At the top, there is an inlet where water can fill the barrel.  At the bottom there is an outlet where water can exit the barrel.  If the inlet at the top of the barrel is closed, it will be impossible to achieve constant, high volume flow out the exit.  Now consider the opposite, where the exit is barely open but the inlet is entirely open and a hose is pouring water in the opening.  It won’t take long before water is overflowing out the opening and there is still very little water coming out the exit.

Turbochargers work on similar principles, only more complex.   Their ability to flow is dependent on the engines ability to move the gasses that are injected into the cylinder for combustion.   For example, if one were to use our Steam STX 71 with a factory exhaust, it is likely that they would be disappointed on the dyno.  The factory exhaust is simply not capable of moving exhaust fast enough for the turbo to spool quickly or make power because the engine can only combust as fast as it can evacuate the exhaust gasses.  Therefore, the more gasses you can create, the more horsepower and torque you will make.  This process is contingent on the ability to move gasses through the system and out the tailpipes.

Sometimes when a customer might state that a turbo is spooling slower than expected, we discover later that there is an exhaust leak somewhere.   Since a turbocharger’s job is to leverage wasted heat from the engine by means of capturing it in the exhaust path, it makes sense that if that heat is leaking off before it reaches the turbo, the turbo will spool slower and produce less power overall.  This one takes us back to our early days in school where we learn about the Law of Conservation of Energy.

Another culprit of a let-down on the dyno can be the wastegate.  The wastegate is called that for a reason.  It’s sole purpose is to waste energy.  This is a good thing when it is tuned properly, and a very bad thing when it is not.  The wastegate’s job is to open when the turbocharger has pressurized the intake manifold to the proper pressure (usually measured in psi).  Let’s assume you are striving to reach 20psi with your tune.  When the turbocharger achieves this, the wastegate on the hotside of the turbo opens up to let exhaust gasses that would normally drive the turbine, escape around the turbine instead of passing through it.  This makes it possible for the turbo to flow at a desired rate without overboosting the engine.  If the wastegate is opening to early, or the spring is insufficient for the tune, exhaust gases that are necessary to make power will be lost along with the power they would have supplied to the engine.

Intercoolers.  We love them and we hate them.  We love them because they cool the air charge going to our engine, lowering the risk of detonation, and giving us much more power than we would have if they were hotter.   Hot intake gasses are less dense, and because of this, supply less oxygen per cubic liter than colder intake gasses.  A warmer intake charge also means that your tuner will have to compensate for those temperatures in power-robbing timing settings.   A good top-mount intercooler will be sufficient for most, however many opt for a front mount intercooler.  There are advantages and disadvantages to both.  Your build and your pocketbook will largely determine what works best for you.  A front mount intercooler means a lot more air is necessary to pressurize the intake system.  This results in power later, but it usually results in lower intake temperatures too.  Also, more piping, means more connections and more connections means more opportunity for leaks.  If you find that your intake is leaking, you’ll know it by a massive loss in power and it taking longer to reach boost.  The air that would have been used to combust a greater amount of fuel is being dumped to atmosphere.  That means less power to the wheels.

Supporting modifications influence your turbocharger’s efficiency.  The fewer you have, the less power you will make.  It is important to consider what other items will be necessary for you to achieve your goals when bolting on a device that is intended to push your vehicles power well beyond what the factory intended.